2/15/2017
Topic:
Kinect or just random command issue
Eric F
|
Any word on this Chris? its been weeks since i've had voice control (i had to unplug the kinects it was so bad) |
9/23/2017
Topic:
Aeon Labs Minimote Config
Eric F
|
Hello! I am having the same issue with my Aeon Labs Minimote.
In Edit Device, the Type is showing up as "Other" with no Keypad option to switch to; and in Add Event, the only options to trigger with the device are when it "Activates"/"Deactivates"...
Any help is much appreciated! |
9/25/2017
Topic:
Aeon Labs Minimote Config
Eric F
|
That fixed it! I had previously added it to the Z-Stick manually via the Z-Stick itself, removing and re-adding via the CastleOS interface got the channels to show up! Thanks Chris! |
10/11/2017
Topic:
Issue with Multiple Event Conditions - System Mode
Eric F
|
I have a few events set up with conditions dependent upon the System Mode... The Idea is that these events should only take place when the Mode is set to "Off" or "Home", and not occur when the Mode is set to "Away" or "Vacation".
These events handle the condition fine when there is only 1 listed, i.e.:
Conditions and System Mode is equal to Off
However when I try to add the second condition, the event never runs, i.e.:
Conditions and System Mode is equal to Off or System Mode is equal to Home
On the chance it was set up differently than most If-Then type structures, I also tried it as below, still with the events never running, i.e.:
Conditions and System Mode is equal to Off and System Mode is equal to Home
edited by efrese on 10/11/2017 edited by efrese on 10/11/2017 |
10/11/2017
Topic:
Issue with Multiple Event Conditions - System Mode
Eric F
|
And as a separate unrelated issue, I have setup my Mini-Mote to change the System Status, with a voice verification to play afterwards to state the Mode changed to... When I hit the buttons, the voice message plays indicating I have changed the Mode, however the GUI never seems to update the Mode listed in the upper right hand corner, so I cannot be sure the Mode is actually changing.
But again, this is unrelated to the above issue, as I have run all my tests after manually changing the System Mode through the GUI. edited by efrese on 10/11/2017 |
10/11/2017
Topic:
Issue with Multiple Event Conditions - System Mode
Eric F
|
Awesome, thanks! |
10/21/2017
Topic:
Issue with Multiple Event Conditions - System Mode
Eric F
|
Chris Cicchitelli wrote:
I can confirm an issue with this release where the "or" is being ignored. I'll have this fixed in the next release coming this week. Thanks for catching this!!
No problem! is that release the "New Beta Version Available" its notifying me about at the top of my portal, or another release?
Chris Cicchitelli wrote:
So while there is a bug, your config is also slightly off. This:
Conditions and System Mode is equal to Off or System Mode is equal to Home
Should be this:
Conditions or System Mode is equal to Off or System Mode is equal to Home
ahhh, Thank you for explaining, i better understand your conditions setup now. I have updated my configs accordingly |
11/11/2017
Topic:
Issue with Multiple Event Conditions - System Mode
Eric F
|
Alright, so downloaded 1.3.3301, was the fix supposed to be in this one, or a later release still coming? |
11/27/2017
Topic:
Kinect is officially dead
Eric F
|
does this mean that any hope of utilizing the camera functionality of the kinects is now gone? |
2/19/2018
Topic:
Issue with Multiple Event Conditions - System Mode
Eric F
|
still showing 1.3.3301 as latest update installed, just wanted to make sure this bug was still on the radar! |
8/25/2018
Topic:
End of the road?
Eric F
|
Hello there, so i followed the above steps to fix the issue. My HUE lights are now working as normal, however my Z-Wave Network keeps showing disabled in the settings, and i am unable to alter the states of those devices. Whenever i go to enable Z-Wave in settings, it reverts itself back to disabled. All my devices are showing in the correct states in the portal, but I am unable to turn them on or off from there (except as i said the hue lights). |
10/1/2018
Topic:
End of the road?
Eric F
|
Any word on why you think my Z-Wave settings keep switching back to "disabled" immediately when i change it to "enabled"? I've been getting by by manually turning things on and off, but it'd be nice to get the majority of my network back online! |
10/1/2018
Topic:
End of the road?
Eric F
|
this is version 1.3.3325, after applying the manual file change over you posted in this thread. |
10/2/2018
Topic:
End of the road?
Eric F
|
so the errors.xml file was extremely large, but also showed up to me as blank... so i replaced it with an older copy of the file i had copied and then repeated the "enable". Please see attached errors.xml file (bottom) for the new z-wave error, because i honestly have no idea what it means.. also errors2.xml is the large blank one if that helps |
11/6/2018
Topic:
End of the road?
Eric F
|
Just curious if you'd had a chance to take a look at the errors document. it doesn't look like the com port is being otherwise used to me, but i'm not an expert at reading these things |